VIP member
Product details
Ulide UT3042B
Ulide UT3042B
TECHNICAL INDEX
basic function |
Technical indicators |
|
passageway |
2 |
|
bandwidth |
40MHz |
|
Sampling method | ||
real-time sampling |
500MS/s |
|
equivalent sampling |
25GS/s |
|
average value |
2 to the power of n, selectable from 2 to 256 times. |
|
input | ||
Input coupling |
DC, AC, Ground (DC, AC, GND) |
|
Input impedance |
1 ± 2% Μ Ω, parallel with 24 ± 3pF |
|
Probe attenuation coefficient setting |
1X,10X,100X,1000X |
|
*Large input voltage |
400V (DC+AC peak, 1 Μ Ω input impedance) (10:1 probe attenuation) |
|
Isolation between channels |
Better than 40:1 |
|
Inter channel time delay (typical) |
150ps |
|
level | ||
waveform interpolation |
sin(x)/x |
|
Recording and Storage |
Storage depth: 1M sampling points |
|
Scanning range (S/div) |
5ns/div ～ 50s/div, 1-2-5 base (60MHz, 80MHz, 100MHz) |
|
Sampling rate and delay time * * degrees |
± 100ppm (any time interval ≥ 1ms) |
|
|
Time interval (△ T)
Measure * * degrees (full bandwidth)
|
Single time: ± (1 sampling interval+100ppm x reading+0.6ns)>16 average values: ± (1 sampling interval+100ppm x reading+0.4ns) |
|
vertical | ||
Analog to Digital Converter (A/D) |
8-bit resolution, simultaneous sampling of two channels |
|
deflection factor |
2mV/div~5V/div (at input BNC) |
|
Displacement range |
±10div |
|
analog bandwidth |
40MHz |
|
Optional simulation bandwidth limitations, typical |
20MHz |
|
Low frequency response (AC coupling, -3dB) |
≤ 10Hz (on BNC) |
|
Rise time (typical on BNC) |
＜8.7ns |
|
DC gain * * degrees |
2mv/div, ± 4% at 5mv/div (sampling or average sampling method);
When 10mv/div~5v/div: ± 3% (sampling or average sampling method)
|
|
DC measurement * * degrees (average sampling method) |
When the vertical displacement is zero and N ≥ 16: ± (4% x reading+0.1div+1mV); Vertical deflection coefficient ≥ 5mV/div; When N ≥ 16: ± [3% x (reading+vertical displacement reading)+(1% x vertical displacement reading)]+0.2div) vertical deflection coefficient from 2mV/div to 200mV/div plus 2mV; vertical deflection coefficient from 500mV/div to 5V/div plus 50mV |
|
Voltage difference (Δ V) measurement accuracy (average sampling method) |
Under the same settings and environmental conditions, after taking the average of ≥ 16 captured waveforms, the voltage difference (Δ V) between any two points on the waveform is ± (3% x reading+0.05div) |
|
trigger | ||
Trigger sensitivity |
DC~10MHz 0.5div 10MHz~Maximum bandwidth 1div |
|
Trigger level range |
internal |
± 10div from the center of the screen |
EXT |
±1.6V |
|
EXT/5 |
±8V |
|
Trigger level * * degree (typical) * * degree is suitable for signals with rise and fall times ≥ 20ns |
inside |
± (0.3div × V/div) (within ± 4div from the center of the screen) |
EXT |
± (6% set value+40mV) |
|
EXT/5 |
± (6% set value+200mV) |
|
Pre triggering capability |
Normal mode/scanning mode, pre trigger/delayed trigger, pre trigger depth adjustable |
|
Release range |
100ns-1.5s |
|
Set the voltage level to 50% (typical) |
Operation under the condition of input signal frequency ≥ 50Hz |
|
Edge triggered | ||
Edge type |
Rising and falling |
|
Pulse width triggering | ||
Trigger mode |
(greater than, less than, equal to) positive pulse width, (greater than, less than, equal to) negative pulse width |
|
Pulse width range |
20ns-10s |
|
Video trigger | ||
|
Trigger sensitivity
(Video triggered, typical)
|
internal |
2div peak to peak value |
EXT |
400mV |
|
EXT/5 |
2V |
|
|
Signal system and line/field
Frequency (video trigger type)
|
Supports standard NTSC and PAL formats, with a line range of 1-525 (NTSC) and 1-625 (PAL) |
|
Alternating triggering | ||
CH1 trigger |
Edge, pulse width, video |
|
CH2 trigger |
Edge, pulse width, video |
|
measure | ||
cursor |
Manual mode |
Voltage difference between cursor (Δ V), time difference between cursor (Δ T), reciprocal of Δ T (Hz) (1/Δ T) |
Tracking mode |
Voltage and time values of waveform points |
|
automatic measurement |
Measurement of peak to peak value, amplitude, * large value, * small value, top value, bottom value, average value, root mean square value, overshoot, overshoot, frequency, cycle, rise time, fall time, positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, delay 1->2 (rise), delay 1->2 (fall) |
|
Mathematical operations |
Add, subtract, multiply, divide, invert |
|
Stored Waveforms |
10 sets of waveforms, 10 settings |
|
FFT |
Window |
Hanning,Hamming,Blackman,Rectangular |
Sampling point |
1024 points |
|
lissajous figures |
phase difference |
±3 degrees |
display | ||
display type |
The diagonal is 145 millimeters (5.7 inches) LCD display |
|
Display Resolution (Display) |
320 horizontal x RGB x 240 vertical pixels (monochrome) |
|
Display Color |
monochrome |
|
Display contrast |
Adjustable |
|
Backlight intensity (typical) |
300nit |
|
Display language types |
Simplified Chinese, Traditional Chinese, English |
|
Probe compensator output | ||
Output voltage (typical) |
About 3V, peak to peak ≥ 1M Ω load |
|
Frequency (typical) |
1kHz |
|
Interface function | ||
Standard configuration |
1 USB (D); 1 USB (H); 1 RS-232C |
|
Select accessories |
GPIB and LAN |
|
Power Supply | ||
supply voltage |
100-240VAC RMS 45Hz to 440Hz, CAT II |
|
consume power |
Less than 30VA |
|
fuse |
2A, T-class, 250V |
|
Environmental Science | ||
temperature |
Operation: 0 ℃~+40 ℃ |
|
Non operational: -20 ℃ to+60 ℃ | ||
cooling method |
convection |
|
humidity |
+10℃~+30℃:≤95%±5%RH, |
|
+30℃~+40℃:≤75%±5%RH | ||
height |
Operate 3000 meters |
|
Non operational 15000 meters | ||
Mechanical specifications | ||
size |
320mm (width) x 150mm (height) x 292mm (depth) |
|
Weight (net weight) |
Excluding packaging |
4.9kg |
Including packaging |
6.8 kg |
|
IP protection |
IP2X |
|
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-