VIP member
TCG Gear (Stainless Steel) CRS&CPS Series
TCG rack achieves a more agile rotary linear transmission through the rolling engagement between the rolling pin of the roller and the tooth surface o
Product details
talent
-
Zero backlash
The teeth (rolling pins) always maintain contact at 2-3 points, and there will be no backlash in the forward and reverse directions.
-
Long distance and high-speed (Rack)
The use of splicing gear gauges can achieve long-distance transmission. It can achieve high-speed travel of over 180m/min.
-
high-precision
The feed accuracy (rotation to line ratio) and positioning accuracy approach precision ball screw.
-
Low noise, low vibration
The rolling pin supported by the needle roller bearing smoothly rolls on the involute gear surface. No unpleasant knocking or rolling sounds occur. At the same time, it also reduces vibration.
-
Low dust emission
Due to the smooth rolling contact and the small diameter and low speed of the rotating part, low wear only generates minimal heat and dust.
- Model representation
- Specification Table
Model representation
roller
The pressing plate bolt is a through threaded bottom hole, so there is no need for bolts with exhaust specifications.
- CPS
- 1
- 1610
- 2
- A
- A
- 4
- A
- 5
- 1. Product Name
- CPS series
- 2. Code
-
1610, 2010, 2510
- 3. Seal in grease
-
A: Standard
G: The customer provides lubricating grease
※ Sealed lubricant: In the case of G (customer provided lubricant), due to the characteristics of the lubricant, it may not reach the sample load value. Please be aware.
- 4. Precise cleaning
-
A: None
S: Yes, there is
Precision cleaning: In the presence of S, vacuum packaging is carried out after rust prevention treatment.
- 5. Lock the bolt
-
A: Standard
B: There is an exhaust hole
- CPS
- 1
- 3212
- 2
- A
- A
- 4
- A
- 5
- 1. Product Name
- CPS series
- 2. Code
-
3212, 4012
- 3. Seal in grease
-
A: Standard
G: The customer provides lubricating grease
※ Sealed lubricant: In the case of G (customer provided lubricant), due to the characteristics of the lubricant, it may not reach the sample load value. Please be aware.
- 4. Precise cleaning
-
A: None
S: Yes, there is
Precision cleaning: In the presence of S, vacuum packaging is carried out after rust prevention treatment.
- 5. Lock the bolt
-
A: Standard
The structure of the expansion sleeve can be vented, and the locking bolts are only standard specifications.
Rack and pinion
- CRS
- 1
- 1610
- 2
- A
- 1. Product Name
- CRS series
- 2. Code
-
1610, 2010, 2510, 3212, 4012
- 3. Installation holes
-
F: Only side holes (standard)
Y: Side hole+bottom threaded hole
- 4. Rack length
- Refer to the rack drawing for rack cutting. Please refer to the product sample and technical Q&A
- 5. Precise cleaning
-
1: No (coated with anti rust oil)
2: Apply standard lubricating grease (Alvania Grease S2 (Shell Japan)) when packaging.
3: Apply the lubricating grease provided by the customer when packaging.
The rack is made of martensitic stainless steel, so the entire surface is treated with rust prevention during packaging.
Under precision cleaning, vacuum package after rust prevention treatment.
Splicing tooth gauge
The splicing tooth gauge is universal with the CRA and CRC series.
- CJ
- 1
- 16
- 2
- B
- 1. Product Name
- CJ series
- 2. Code
- 16. 20, 25, 32, 40
material
The materials used in the product are as follows.
rack
Use martensitic stainless steel.
roller
Use martensitic stainless steel.
| Roller body | austenitic stainless steel |
| Pressing board | |
| bolt | |
| Rising set | |
| roll pin | martensitic stainless steel |
| oil seal | Nitrile rubber (NBR) |
Splicing tooth gauge
Carbon steel for mechanical construction.
Specification Table
|
model
project
|
||
|---|---|---|
| roller | ||
| rack | ||
| CPS/CRS series | ||||
|---|---|---|---|---|
| CPS1610A | CPS2010A | CPS2510A | CPS3212A | CPS4012A |
| CRS1610A | CRS2010A | CRS2510A | CRS3212A | CRS4012A |
| General specifications | Basic dynamic rated load | N |
|---|---|---|
| Maximum usage load | N | |
| Allow static rated load | N | |
| Basic dynamic rated torque ※ Note 1 | N・m | |
| Maximum applicable torque ※ Note 1 | N・m | |
| Allowable static rated torque ※ Note 1 | N・m | |
| The distance traveled by the roller rotating once | Mm/rotation | |
| Maximum pressure angle | ° | |
| Modulus (roller P.C.D/number of teeth) | mm | |
| Roller | number of teeth | tooth |
| Node diameter ※ Note 2 | mm | |
| quality | kg | |
| Moment of inertia | ×10-4kg・m2 | |
| rack | pitch | mm |
| Cut-to-length | mm | |
| number of teeth | tooth | |
| quality | kg | |
| Outline Drawing | Roller/rack | |
| Splicing tooth gauge | ||
| cad data | Roller/rack | |
| Splicing tooth gauge | ||
| Product samples | ||
| operation instructions | ||
| 1000 | 1500 | 2200 | 3600 | 6000 |
| 1700 | 2200 | 3100 | 6600 | 9000 |
| 2000 | 3000 | 4400 | 7200 | 10940 |
| 25.5 | 47.7 | 87.5 | 220.0 | 458.4 |
| 43.3 | 70.1 | 123.4 | 403.3 | 687.6 |
| 59.9 | 95.5 | 175.1 | 440.0 | 836.0 |
| 160 | 200 | 250 | 384 | 480 |
| 30.7 | 30.1 | 30.7 | 30.1 | 30.0 |
| 4.75 | 6 | 7.5 | 9.5 | 12 |
| 10 | 10 | 10 | 12 | 12 |
| 50.9 | 63.7 | 79.6 | 122.2 | 152.8 |
| 0.81 | 1.5 | 2.4 | 6.8 | 16 |
| 4.56 | 12.5 | 29.6 | 200 | 728 |
| 16 | 20 | 25 | 32 | 40 |
| 992 | 1000 | 1000 | 992 | 1000 |
| 62 | 50 | 40 | 31 | 25 |
| 2.2 | 4.1 | 5.4 |
8.3 |
13 |
PDF |
PDF |
PDF |
PDF |
PDF |
PDF |
PDF |
PDF |
PDF |
PDF |
CAD |
CAD |
CAD |
CAD |
CAD |
CAD |
CAD |
CAD |
CAD |
CAD |
|
PDF
|
||||
|
PDF
|
||||
Note 1: Basic dynamic rated torque (maximum operating torque, allowable static rated torque) refers to the torque generated by the basic dynamic rated load (maximum operating load, allowable static rated load) loaded on the diameter of the roller pin pitch circle.
Note 2: This is a theoretical value, not the actual pitch diameter of the rolling pin.
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-