electricityElectricity

power:three-phase380V/50HzVoltage:±5%，

Power: 3-phase 380V/50Hz;

vaporReference parameter table:

Steam

Maximum steam0.61Mpa，160°C ,minimum0.4Mpa，144°C .Without using electric heating assistance, 0.5Mpasaturated steamThe temperature is150℃,ifUse inside the boxThe temperature must be120degree,thenvapor pressurePower should be5.03kg/m2.

rule grid

inside Rong

Steam ovenTSZQ-104P

An pretend use ruler inch

Specification Model

(Depth x Width x Height)

studio dimensions

2700×1150×1550mm

Dimensions approximately

2900*1540+Control box width250*1950+Fan height300mm

The overall external dimensions are approximately

3100*1790*2250

splicing process

Each joint is sealed with silicone rubber high-temperature resistant sealant.

Steam heating position

Steam pipes are distributed on both sides. The steam interface is located on the back.

Fan power:

1100W *2Equipped with a 12 inch fan blade oven top

Bottom fixed

Directly placed on the ground, the bottom 14 groove 304 channel steel is basically flush with the ground, making it convenient for the trolley to push

internal

Internally equipped with 2 small carts made of 304 square tubes, each cart can hold 52 trays with a size of 460 * 640 * 45MM. The outer diameter of the cart is D1300 * W1050 * H1550MM

Lord want skill technique ginseng number

On site environmental conditions

temperature5-40℃ Relative humidity: not greater than85% Suitable for indoor use

There is no strong vibration or airflow around No corrosive gases or chemicals present

Non drying flammable and explosive materials

Equipment Composition

Composed of furnace body, hot air circulation system, electric heating system, intake and exhaust system, circuit control system, etc

electricity source

3N+PE 380V 50Hz

Temperature range for use

Room temperature~150℃ (adjustable arbitrarily)

warm-up time

≤ 30 minutes, empty furnace test（Actually, based on the customer's existing steam pressure）

heating parameters

twoFin shaped assemblyWThe shaped steam pipe is installed in the air ducts on both sides of the oven, separated from the working room, with a continuous service life of more than 50000 hours, energy-saving and environmentally friendly.

thickness of insulation layer

100K grade high-density aluminum silicate fiber insulation, insulation layer thickness 100MM

stove body be unify knot constitute

structural form

Adopting a monolithic structure.Concentrated placement

Opening method

Front double door of furnace body.(The door lock adopts a handle and steel hinge)

Furnace shell

SU304Stainless steel plate 12MM

Furnace inner liner

SU304Stainless steel plate 12MM

Shell skeleton

Q235channel steel12Number, angle steel8Rust removal and rust prevention treatment

Inner liner skeleton

Q235angle steel8After rust removal and rust prevention treatment, spray paintW61Series of silicone heat-resistant paint

bottom plate

Q235channel steel12After rust removal and rust prevention treatment, spray paint851Moisture resistant coating.

sealing material

high temperature resistancesilicone rubbersealing strip

drum wind be unify

Working Principle:

Air is blown by a high air volume blowerblowEntering the air duct, compared to inside the air ductplusAfter heat exchange, the heat element is blown out from the air vents on both sides of the air duct, enters the working chamber for heat exchange with the workpiece, and then returns to the blower motor through the top return air plate, thus forming a cyclic hot air circulation. Simultaneously using porous plates for air volume regulation ensures good temperature uniformity within the workspace.

air supply mode

Studio hot air supply method: strong pressure vertical and horizontal air supply

blower motor

High temperature resistant long shaft motor specifically designed for curing furnaces, with a noise level of65dBbelow

blast

1400 RPM, multi wing stainless steel high air volume centrifugal silent fan wheel

Installation position of motor

Installed externally at the top of the furnace, the long axis extends into the air duct at the top of the working room through the insulation layer

enter\\\\exhaust system

intake valve

Top fan base air inlet2A diameter of 60MM

exhaust valve

A manual stainless steel exhaust valve is installed in front of the top1One, with a diameter of 100MM (adjustable according to the required displacement). The supplier shall reserve flange interfaces and provide external exhaust pipes according to the actual situation in the workshop.

Install exhaust system

Install an exhaust system. When the water vapor inside the box is too high, the exhaust system can be turned on to help dissipate heat and accelerate material drying.

electricity control be unify

control manufacture cabinet

Using an independent control cabinet for control,Stainless steel electrical cabinetLocated on the front of the ovenrightSide by side. Separating from the box is beneficial for protecting the heat dissipation of electrical components.

Lord control table

Digital display intelligent instrument XGQ-A2100FAutomatic temperature control, constant temperature and beltPIDAdjust. Control accuracy ±1℃.

Overtemperature protection instrument

Digital display instrument,Automatic temperature control, constant temperature and beltPIDAdjust. Control accuracy ±1℃.

Time setting device:

HS48S-99.99 timing device, can be manually/automatically turned on/off. It starts timing when the temperature reaches the set temperature, and cuts off the heating power when the time reaches the set range.

temperature measuring device

A stainless steel tubeKThe temperature sensing device is sensitive, accurate, and has a long service life for temperature measurement. Installed in the side air duct of the box.

electrical components

Adopting domestic and foreign famous brands, such as Chint, Omron, etc

heating control

Suzhou Integrated ElectronicsSSRSolid state relays have contactless power regulation and use input stages with optoelectronic isolation,

TTLLevel compatible input, DC or pulse triggered, with no contacts and no mechanical moving parts,

No sparks, no movement noise, vibration resistance, long lifespan and other characteristics.

guarantee

protect

be

unify

match

place

●Automatically cut off the heating power supply.

●Overtemperature protection: When the specified temperature is exceeded, the buzzer will sound an alarm, the heating will be cut off, and the fan will not stop rotating to help dissipate heat inside the box.

● Motor and heating interlock control Start with the blower before heating to prevent the heater from burning out and causing accidents.

● Motor overload protection Prevent the motor from burning out and tripping.

● Short circuit protection for electric heaters Prevent electric heaters from short circuiting and burning out

● Control circuit protection Prevent short circuits in the circuit and prevent accidents

● circuit breaker Prevent overload and short circuit of the main circuit, which may cause accidents

● Power prevention after power outage Prevent damage to baked goods caused by increased baking time after power on

● Grounding protection: Safety grounding protection for structural components.

● Power phase loss and phase sequence protection: equipped with phase sequence protector

solid transform stove Appendix document and its it say bright

random file

Instruction Manual1copy/Taiwan

Various instrument manuals1set/Taiwan

Precautions

Top 4 lifting rings for easy hoisting