Soft water treatment equipment accessories - fiberglass anti winding soft water tank-Fornitore globale

No. 18 Niushan Road, Dongcheng Economic Development Zone, Linqu County, Weifang City, Shandong Province (Huahai Building)

1、 Characteristics

1. The process of water softening has a high degree of automation

Softening water equipment usually adopts control devices with strong human-computer interaction capabilities to achieve the process of ion exchange and resin regeneration, and the entire process is automated.

2. High efficiency

The design of softened water is reasonable, which can fully utilize the potential of the resin and greatly increase its water production capacity.

3. Save manpower

The entire process is automated, and water production tasks can be completed in a timed and quantitative manner through control equipment, without the need for specialized personnel. Installation is also relatively simple and convenient.

4. Non toxic and pollution-free

The material uses lead-free brass or engineering plastic, which is environmentally friendly, scientific, and pollution-free. Users can use it with confidence.

5. Save water resources

The water treatment rate can completely reach over 98%, considering the needs of users and saving water consumption and water treatment costs.

6. Save electricity

Advanced siphon silent Xu salt pump is adopted.

7 Easy to adjust

It can control the equipment to adjust the regeneration cycle and time.

8 Anti corrosion

The tank adopts non drying equipment, which can withstand various clothing and is suitable for long-term storage in mixed solutions of various particles, and can also avoid resin pollution.

9. Wide applicability

It can be used for water treatment of industrial boilers, air conditioning systems, bathing equipment, heat exchangers, and the electronics industry.

2、 Working principle

2RNa + Ca2+ = R2Ca + 2Na+

2RNa + Mg2+ = R2Mg + 2Na+

This equation indicates that after the plum enters the exchanger, Ca+and Mg+in the water will undergo corresponding reactions and be replaced by Na+.

The general control process is: operation, backwashing, salt suction, slow washing, salt tank replenishment, and forward washing.

After the resin absorbs a large amount of calcium and magnesium particles, it needs to be regenerated. The regeneration process is to rinse the resin layer with salt water from a single valve and tank salt tank of a chemical water equipment, and use the characteristic of ion displacement to displace the hardness ions on the resin. The resin is discharged from the tank with the regeneration waste liquid, and the softening exchange function of the resin is restored, which can be put back into production again.

3、 Workflow

Backwash: After working for a considerable period of time, the equipment will intercept a large amount of calcium, magnesium particles and various pollutants brought by the raw water on the upper part of the resin. After removing these pollutants bit by bit, the ion exchange resin can be completely exposed and reused, and the regeneration effect can be guaranteed to a certain extent.

Salt absorption: The process of injecting salt water into a resin tank. Traditional equipment uses a salt pump to manually inject salt water, while fully automatic equipment uses a device control system to suck in salt water through a dedicated built-in sprayer.

Slow flushing: After flowing salt water through the resin at a certain flow rate, the process of slowly infiltrating and replacing the residual salt in the resin with raw water at the same flow rate is called slow flushing, also known as replacement. This process is similar to the process of salt absorption and usually takes about 30 minutes.

Quick flushing: In order to flush away residual salt, a flow rate similar to the actual working method and technology should be used to control the flow rate of the resin with raw water. The effluent quality of this process should be soft water that meets the standard. Generally, the fast flushing process takes 5-15 minutes.

4、 Job requirements

Working temperature: 1-55 ℃

Source water hardness:<8mmol/L

Operation mode: automatic/manual

Water hardness: ≤ 0.03mmol/L

Regeneration agent: NaCl Regeneration method: co current/counter current

Exchange agent: 001 * 7 strong acidic ion exchange resin

5、 Application scope

This device has a wide range of applications and can be widely used for softening the supply water of steam boilers, hot water boilers, exchangers, evaporative condensers, air conditioners, direct fired engines, and other industrial projects. It can also be used for the treatment of domestic water in hotels, restaurants, office buildings, apartments, homes, and targeted softening water treatment in industries such as food, beverage, brewing, laundry, printing and dyeing, chemical, pharmaceutical, etc.

6、 Technical indicators

1. Work pressure: 0.2-0.6MPa; 0.3MPa;

2. Raw water hardness: ≤ 8mmol/L (if the raw water hardness is>8mmol/L, redesign is required, please contact the company for inquiry);

3. Water hardness: 0.03mmol/L (calculated as 1/2Ca2+, 1/2Mg2+);

4. Raw water temperature: 5 ℃ -50 ℃

5. Power supply: AC220V, 50Hz;

Power: 10-40W

Water consumption<2% of water production, salt consumption<100 grams per gram equivalent

Electricity consumption: 10W-40W, as there is no need for a salt pump, the electricity consumption is only 1% of that of typical softened water equipment

7、 Product advantages

The structural domain material of this product is selected as PE material for the inner lining, and the outer layer is made of resin and glass fiber wrapped tightly, which is not easy to peel off and is corrosion-resistant.

The winding fiberglass tank body has no pollution to the water source and is equipped with upper and lower flange connections.

This equipment is suitable for making tanks for softened water for civilian and industrial use.