rule grid

inside Rong

ovenTSPLC-3060

An pretend use ruler inch

Install filter

studio dimensions

1700×1500×1200mm(Width (between two doors, distance) x Depth x Height

Dimensions approximately

2140+Control Box Width 300*1700*1580mm+Motor height 270 (width x depth x height)

base

Groove track facilitates the pushing of small cars

material rack

empty box

Lord want skill technique ginseng number

On site environmental conditions

Temperature:5-40℃ Relative humidity: not greater than85% Suitable for indoor use

There is no strong vibration or airflow around No corrosive gases or chemicals present

Non drying flammable and explosive materials

Equipment Composition

Composed of furnace body, hot air circulation system, electric heating system, intake and exhaust system, circuit control system, etc

electricity source

3N+PE 380V 50Hz

Temperature range for use

Room temperature~300 ℃ (adjustable arbitrarily)

warm-up time

≤ 30-50 minutes, empty furnace test

Temperature Uniformity

≤±2.5％℃[national standard]

temperature fluctuation

≤±1℃;[national standard]

heating rate

6-7 ℃ per minute

Surface heating of the box:

Surface temperature not exceeding room temperature plus 25 ℃

heating power

18KW (Two sets of U-shaped heating tubes installed in the air ducts on both sides of the drying oven, separated from the working room, with a continuous service life of more than 50000 hours, and more energy-efficient heating use)

insulation thickness

100K grade high-density aluminum silicate fiber insulation, insulation layer thickness 100MM

stove body be unify knot constitute

structural form

Adopting a monolithic structure.Concentrated placement

Opening method

Front double door of furnace body.(The door lock adopts chrome plated sheep horn handle and steel hinge)

Furnace shell

Cold rolled steel plate with a thickness of 1.2mm, after rust prevention treatment, sprayed with acrylic self drying paint

Furnace inner liner

SUS304 stainless steel with a thickness of 1.0mm, treated with silver powder paint

Shell skeleton

Q235Rust removal and rust prevention treatment for channel steel and angle steel

Inner liner skeleton

Q235After rust removal and rust prevention treatment of angle steel, spray coatingW61Series of silicone heat-resistant paint

bottom plate

Q235After rust removal and rust prevention treatment of channel steel, spray coating851Moisture resistant coating.

sealing material

Aluminum silicate resistant asbestos sealing strip

drum wind be unify

Working Principle:

Air is blown by a high air volume blowerblowAfter entering the air duct, it exchanges heat with the electric heating elements inside the duct and is blown out from the air outlets on both sides of the duct. After entering the working chamber and exchanging heat with the workpiece, it returns to the blower motor through the top return air plate, thus forming a continuous hot air cycle. Simultaneously using porous plates for air volume regulation ensures good temperature uniformity within the workspace.

air supply mode

Studio hot air supply method: horizontal air supply on both sides

Blower motor

High temperature resistant long shaft motor specifically designed for curing furnaces, with a noise level of65dBthe following

Blast power

1400 RPM, 2 * 1100W fan with 230 * 165MM multi wing high air volume centrifugal silent impeller

Installation position of motor

Installed externally at the top of the furnace, the long axis extends into the air duct at the top of the working room through the insulation layer

enter\\\\exhaust system

intake valve

Top fan base with 2 air intakes, diameter 60MM

exhaust valve

One manual exhaust valve with a diameter of 100MM is installed on the side (the size can be adjusted according to the required exhaust volume). The supplier reserves flange interfaces, and the external exhaust pipes are customized by the user according to the actual situation in the workshop.

electricity control be unify

control manufacture cabinet

Adopting an independent control cabinet for control, the surface of the control cabinet is treated with spraying and painting. Located on the left side of the front of the oven..

PLC control

Human computer interface, program control, capable of computer output. With a password, it can be self-locking.

Nitrogen filling device

Battery valve controls nitrogen charging

Overtemperature protection instrument

Overtemperature protector, when the specified temperature is exceeded, the buzzer will sound an alarm, automatically cut off heating, and the fan will not stop rotating to help dissipate heat.

temperature measuring device

A stainless steel tubeKThe temperature sensing device is sensitive, accurate, and has a long service life for temperature measurement. Installed inside the air duct of the box.

electrical components

Adopting domestic and foreign famous brands, such as Chint, Omron, etc

heating control

Suzhou Integrated ElectronicsSSRSolid state relays have contactless power regulation and use input stages with optoelectronic isolation,

TTLLevel compatible input, DC or pulse triggered, with no contacts and no mechanical moving parts,

No sparks, no movement noise, vibration resistance, long lifespan and other characteristics.

guarantee

protect

be

unify

match

place

● Automatically cut off the heating power supply.

● Overtemperature protection: If the specified temperature is exceeded, the buzzer will sound an alarm and the heating will be cut off.

● Motor and heating interlock control Start with the blower before heating to prevent the heater from burning out and causing accidents.

● Motor overload protection Prevent the motor from burning out and tripping.

● Short circuit protection for electric heaters Prevent electric heaters from short circuiting and burning out

● Control circuit protection Prevent short circuits in the circuit and prevent accidents

● circuit breaker Prevent overload and short circuit of the main circuit, which may cause accidents

● Power prevention after power outage Prevent damage to baked goods caused by increased baking time after power on

solid transform stove Appendix document and its it say bright

random file

Instruction Manual1copy/Taiwan

Various instrument manuals1set/Taiwan