rule grid

inside Rong

Steam oven

An pretend use ruler inch

Specification Model

(Depth x Width x Height)

Oil drum size

Φ590*High890MM

studio dimensions

1400*（1400+160+1400）*1500

Dimensions approximately

1580*3300+Control box width 250*1980+Fan height 270mm

Steam heating position

The steam pipes are distributed on both sides, and the steam interface is on the back.

Fan power:

750W *4match10.5Top of inch blade oven

Bottom fixed

Channel steel feet

internal

2apalletEach onebracketCan be inserted4An oil drumThe size is: deep1300 * width 1300MM * height 180MM, with a forklift foot height of 120MM placed at the bottom

Lord want skill technique ginseng number

On site environmental conditions

temperature5-40℃ Relative humidity: not greater than85% Suitable for indoor use

There is no strong vibration or airflow around No corrosive gases or chemicals present

Non drying flammable and explosive materials

Equipment Composition

Composed of furnace body, hot air circulation system, intake and exhaust system, circuit control system, etc

electricity source

3N+PE 380V 50Hz

Temperature range for use

Room temperature~100 ℃ (adjustable arbitrarily)

warm-up time

≤50Minutes, empty furnace test

Temperature Uniformity

≤±2.5％℃[National Standard]

heating parameters

Three sets of fin typeWThe shaped steam pipe is installed in the air ducts on both sides of the oven, separated from the working room, with a continuous service life of more than 50000 hours, energy-saving and environmentally friendly.

thickness of insulation layer

100K grade high-density aluminum silicate fiber insulation, insulation layer thickness 100MM

stove body be unify knot constitute

structural form

Adopting a monolithic structure.Concentrated placement

Opening method

Front of furnace bodyOuter middle pillar2 of themsingleOpen the door.(The door lock adopts a handle and steel hinge)

Furnace shell

Cold rolled steel plate 1.0mm

Furnace inner liner

SU304 stainless steel plate 1.0mm

Shell skeleton

Q235Rust removal and rust prevention treatment for channel steel No. 10 and angle steel No. 6

Inner liner skeleton

Q235After rust removal and rust prevention treatment of angle steel No. 6, spray coatingW61Series of silicone heat-resistant paint

bottom plate

Q235After rust removal and rust prevention treatment of channel steel No. 10, spray paint851Moisture resistant coating.

sealing material

High temperature resistant silicone rubber sealing strip

drum wind be unify

Working Principle:

Air is blown by a high air volume blowerblowAfter entering the air duct, it exchanges heat with the heating elements inside the duct and is blown out from the air outlets on both sides of the duct. After entering the working chamber and exchanging heat with the workpiece, it returns to the blower motor through the top return air plate, thus forming a cyclic hot air circulation. Simultaneously using porous plates for air volume regulation ensures good temperature uniformity within the workspace.

air supply mode

Studio hot air supply method: strong pressure vertical and horizontal air supply

blower motor

High temperature resistant long shaft motor specifically designed for curing furnaces, with a noise level of65dBbelow

blast

1400 RPM, multi wing stainless steel high air volume centrifugal silent fan wheel

Installation position of motor

Installed externally at the top of the furnace, the long axis extends into the air duct at the top of the working room through the insulation layer

enter\\\\\\\\\\\\\\\\exhaust system

intake valve

Top fan base air inlet4A diameter of 60MM

exhaust valve

Two manual stainless steel exhaust valves with a diameter of 100MM are installed in front of the top (the size can be adjusted according to the required exhaust volume). The supplier shall reserve flange interfaces and provide external exhaust pipes according to the actual situation in the workshop.

electricity control be unify

control manufacture cabinet

Adopting independent control cabinet and stainless steel electrical cabinet for control. Located on the right side of the front of the oven. Separating from the box is beneficial for protecting the heat dissipation of electrical components.

Lord control table

Digital display intelligent instrument XGQ-A2100FAutomatic temperature control, constant temperature and beltPIDAdjust. Control accuracy ±1℃.

totalTime setting device:

HS48S-99.99 timing device, capable of manual/automatic switching,Start timing.

Installation time control2 of them

effect; It can correspond to the constant temperature timer of the gate separately.When the temperature reaches the set temperature, the timer starts, and when the time reaches the set rangeBuzzer alarm prompt.

temperature measuring device

oneStainless steel supportKThe temperature sensing device is sensitive, accurate, and has a long service life for temperature measurement. Installed in the side air duct of the box.

electrical components

Adopting domestic and foreign famous brands, such as Chint, Omron, etc

heating control

Suzhou Integrated ElectronicsSSRSolid state relays have contactless power regulation and use input stages with optoelectronic isolation,

TTLLevel compatible input, DC or pulse triggered, with no contacts and no mechanical moving parts,

No sparks, no movement noise, vibration resistance, long lifespan and other characteristics.

guarantee

protect

be

unify

match

place

● Motor and heating interlock control Start with the blower before heating to prevent the heater from burning out and causing accidents.

● Overtemperature protection: When the main temperature control meter fails and the temperature inside the box exceeds the specified temperature, the overtemperature protection instrument will automatically cut off heating, and the fan will not stop running to help dissipate heat.

● Motor overload protection Prevent the motor from burning out and tripping.

● Short circuit protection for electric heaters Prevent electric heaters from short circuiting and burning out

● Control circuit protection Prevent short circuits in the circuit and prevent accidents

● circuit breaker Prevent overload and short circuit of the main circuit, which may cause accidents

solid transform stove Appendix document and its it say bright

random file

Instruction Manual1copy/Taiwan Various instrument manuals1set/Taiwan