Changchun Ceramic Fiber Box type Resistance Furnace Special Offer Priceoverview

SX₃The series 1000 ℃ box type resistance furnace is a periodic operation electric furnace, which can be used for chemical analysis, physical measurement, and general small steel heat treatment heating in industrial and mining enterprises, scientific research units, laboratories, etc.

This series of resistance furnaces is equipped with KSW or DRZ temperature controllers and nickel chromium nickel silicon thermocouples, which can measure, indicate, and automatically control the furnace temperature.

Changchun Ceramic Fiber Box type Resistance Furnace Special Offer PriceMain technical parameters

3、 Structure Introduction

This series of resistance furnace shells are made of thin steel plates that are folded and welded together. The furnace is composed of a box shaped integral lining made of ceramic fiber material. Heating element OcR25A15 iron chromium aluminum alloy wire is wound into a spiral shape and threaded through the wire grooves on the upper, lower, left, and right sides of the furnace lining. The wire groove is connected to the furnace, allowing the heating element to directly radiate heat to the furnace. This type of open furnace lining can effectively accelerate the heating rate of the furnace and improve the accuracy of temperature control.

The electric furnace door is fixed to the electric furnace panel through the long arm of multi-level hinges. The furnace door rotates flexibly. When closing, press or push the handle to fasten the door hook, and the furnace door can be tightly attached to the furnace mouth. When opening, simply lift the handle slightly upwards or inwards, unhook it, and place the furnace door on the side.

The thermocouple used for temperature measurement is inserted through an open hole.

4、 Structural diagram

SX3-2.5/4-10X Electric Furnace Outline Dimensional Drawing

SX3-8/12-10X Electric Furnace Outline Dimensional Drawing

5、 (1) Wiring diagram of electric furnace and temperature controller

（2） Wiring diagram of electric furnace and temperature controller

6、 Installation and use

1. Electric furnaces do not require special installation, they only need to be placed on a flat ground or rack. The controller should avoid vibration and should not be placed too close to the electric furnace to prevent overheating and prevent electronic components from working properly.

2. Insert the thermocouple into the temperature measuring hole behind the furnace, and fill the gap between the hole and the thermocouple with asbestos rope. When connecting the thermocouple and the controller, be careful not to connect the positive and negative poles in reverse.

3. Open the controller casing and connect the power cord, electric furnace wire, and thermocouple wire according to the standard. An additional power switch needs to be installed at the power cord entry point to control the main power supply. Due to the fact that the power supply wire on the controller shares the neutral wire system with the electric furnace wire. The phase line and the neutral line cannot be reversed, otherwise the controller cannot work properly. For safety reasons, both the electric furnace and the controller must be grounded.

4. After checking the wiring is correct, cover the controller housing and set the temperature according to the instrument manual.

The heating and constant temperature of the electric furnace are indicated by red and green indicator lights, with green light indicating heating and red light indicating constant temperature.

7、 Maintenance and Precautions

When the electric furnace is used again after * times of use or long-term disuse, it must be dried in an oven at room temperature――200 ℃ for 2 hours, 200 ℃――600 ℃ for 2 hours, the furnace temperature should not exceed high temperature during use to avoid burning the electric heating element, and it is forbidden to pour various liquids and dissolved metals into the furnace.

2. The electric furnace must be operated in a location with a relative humidity not exceeding 85%, free from conductive dust, explosive gases, and corrosive gases that can damage metal insulation and be harmful to electronic components.

3. Regularly check whether the conductivity system of the electric furnace and controller is in good condition.

4. The furnace temperature shall not exceed the high temperature.

8、 Complete set list

9、 Order Notice

The following items must be specified when placing an order

① Model and name of electric furnace

② Quantity required

10、 Simple fault phenomena and troubleshooting